As an Amazon Associate I earn from qualifying purchases. This write-up is based on manufacturer specifications and published documentation, not hands-on testing.
Native Instruments Komplete Audio 2 moves up from Komplete Audio 1 with two combo inputs and balanced TRS outputs, the right pairing for two-mic recordings and studio monitors.
What the Native Instruments Komplete Audio 2 is
Komplete Audio 2 has two combo inputs, each switchable between mic, line and instrument, with a global 48 V phantom switch. Outputs are two balanced TRS jacks plus a front headphone output with independent volume.
A monitor control blends the direct input with computer playback, so you can hear yourself without latency while still hearing the track. It is bus powered and converts at up to 24-bit/192 kHz.
Specs at a glance
| Spec | Native Instruments Komplete Audio 2 |
|---|---|
| Inputs/outputs | 2-in/2-out |
| Mic preamps | 2 |
| Preamp gain | not published on the pages we checked |
| Mic EIN | not published on the pages we checked |
| Conversion | 24-bit/192 kHz |
| Connection | USB 2.0 |
| Power | USB bus powered |
| I/O detail | 2 combo inputs switchable to mic, line or instrument, global 48 V phantom switch, 2 balanced TRS outputs, 1 headphone output |
Specifications are taken from the Native Instruments Komplete Audio 2 product page and related manufacturer documentation.
A guitar-and-vocal take
A singer and guitarist record together with one mic each. Each combo input switches between mic, line and instrument. Balanced TRS outputs feed studio monitors with less noise.
Features worth knowing
- Two combo inputs with mic/line/instrument switching.
- Balanced TRS outputs.
- Input/host monitor blend.
- Top-panel level meters.
- Bus powered.
Three modes per input
Each combo input switches between mic, line and instrument. That matters because the same jack has to suit a condenser mic one day and a synth the next. Instrument mode raises the input impedance for guitar pickups; line mode suits keyboards and drum machines. Choosing the wrong mode does not usually damage anything, but it changes tone and level, so it is worth checking before a take. Balanced TRS outputs then send your mix to studio monitors with better noise rejection than RCA.
What it does not do
One global phantom switch covers both inputs. That is fine for two condensers or a condenser and a dynamic, but take care with ribbon mics. It is bus powered with one headphone output.
Upgrading from one input
Moving from Komplete Audio 1 to 2 doubles the mic inputs and switches to balanced outputs. If you record duets, interviews or stereo acoustic guitar, that second preamp is the reason to choose it. If you use studio monitors, the balanced TRS outputs reduce noise, especially with cables longer than a metre or two. It remains bus powered and compact, so it still suits a laptop setup.
A two-person setup works well with Komplete Audio 2: two mics for a duet or interview, balanced outputs to studio monitors and direct monitoring to hear both without delay.
Feature notes
Bus power in practice
Bus power suits small interfaces. If the unit behaves oddly on a laptop, try a different port, a shorter cable or a powered hub before assuming a fault.
Instrument (Hi-Z) inputs
Guitar and bass pickups need a high-impedance input to sound right. A Hi-Z input provides that, so you can plug in directly without a DI box. Plugging a guitar into a line input instead often sounds thin and dull.
How much preamp gain do you need?
Gain figures matter most when you use low-output microphones. A condenser on a loud singer barely touches the gain knob, while a broadcast dynamic on a quiet voice can push it to the top, where noise becomes audible. Look at the published gain figure alongside your mic’s sensitivity rather than treating the number as a quality score.
Choosing a sample rate
Choose the sample rate before you start a project and keep it consistent. Changing it mid-project causes playback at the wrong speed or forced conversions.
Latency and buffer size
Buffer size is a trade-off: low for tracking, high for mixing. Switching it between those stages is one of the easiest ways to keep sessions smooth.
Compared with similar interfaces
| Interface | I/O | Mic preamps | Connection | Power |
|---|---|---|---|---|
| Native Instruments Komplete Audio 2 | 2-in/2-out | 2 | USB 2.0 | USB bus powered |
| Arturia MiniFuse 2 | 2-in/2-out | 2 | USB-C | USB bus powered |
| Behringer UMC202HD | 2-in/2-out | 2 | USB 2.0 | USB bus powered |
Arturia MiniFuse 2 adds MIDI and loopback. Behringer UMC202HD is a lower-cost two-preamp option. Our roundup of the best audio interfaces puts these in a wider context.
Our take
The difference between Komplete Audio 1 and 2 matters more than the name suggests. Komplete Audio 2 adds a second combo input, so two mics can be recorded together, and moves to balanced TRS outputs that suit studio monitors better than RCA. The single phantom switch applies to both inputs, which is fine for most setups but worth knowing if you pair a condenser with a ribbon mic.
Is the Native Instruments Komplete Audio 2 right for you?
- Singer-songwriters
- Two-mic podcasts
- Stereo synth recording
Look elsewhere if
- Anyone needing MIDI
- Streamers wanting loopback
- Users needing per-channel phantom
Once you have confirmed it fits, the Native Instruments Komplete Audio 2 on Amazon lists the full package contents.
Native Instruments Komplete Audio 2 setup checklist
- Install the NI driver via Native Access.
- Connect USB.
- Set each input to mic, line or instrument.
- Engage phantom only if needed.
- Connect monitors via TRS.
Avoid these mistakes
- Using phantom with a sensitive ribbon mic on the other channel.
- Leaving an input on the wrong mode.
- Expecting MIDI.
More from our recording section: buffer size, guitar recording levels, our recording guides.
How to set up the Native Instruments Komplete Audio 2
The Native Instruments Komplete Audio 2 is a two-input, two-output interface with few controls. Setup takes about fifteen minutes. Follow these steps once, then save a DAW template.
- Install the driver on Windows. Use Native Instruments’ Komplete Audio driver for ASIO support. On a Mac, Core Audio works without a driver.
- Connect USB. The interface is bus powered over USB 2.0. Plug it straight into the computer, not a passive hub.
- Turn levels down. Set both gain knobs and the big volume knob to minimum before powering speakers.
- Connect monitors. The main outputs are balanced ¼-inch jacks. Use TRS-to-TRS or TRS-to-XLR cables.
- Choose the device. On Windows, select the NI ASIO driver in the DAW. On a Mac, choose Komplete Audio 2.
- Set rate and buffer. Pick 44.1 or 48 kHz for most projects. The unit supports up to 192 kHz. Start at 128 samples for tracking.
- Use +48 V only for condensers. Leave phantom power off for dynamic mics.
For driver details, Native Instruments’ support article on optimising interface settings covers ASIO and Core Audio choices.
Workflow: two mics at once
Two combo inputs are the main step up from the Komplete Audio 1. Each takes an XLR mic or a ¼-inch line or instrument cable.
- Duo podcast: one dynamic mic per host, recorded to two tracks.
- Acoustic guitar in stereo: one mic near the 12th fret and one near the body, at equal distances.
- Singer-guitarist: vocal mic on input 1, guitar DI or mic on input 2.
- Stereo keyboard: left and right outputs into inputs 1 and 2, set to line.
First, set each gain separately on the loudest moment. Next, check both tracks for clipping. Then, for stereo pairs, pan them hard left and right in the DAW.
Workflow: guitar DI and amp sims
Plug a guitar into either combo input and switch it to instrument. Then load an amp simulator on the track. Keep the buffer low, around 64 or 128 samples, so the sound responds quickly to your playing.
Also, record the clean DI signal rather than printing the amp sound. As a result, you can change the amp tone later without replaying the part. Our guide to guitar recording levels suggests safe input targets.
Komplete Audio 2 vs similar interfaces
The table compares the Komplete Audio 2 with its siblings and a common rival. Figures come from each maker’s published specifications.
| Feature | Komplete Audio 1 | Komplete Audio 2 | Komplete Audio 6 | Behringer UMC202HD |
|---|---|---|---|---|
| Mic inputs | 1 | 2 combo | 2 combo | 2 combo |
| Extra line inputs | 1 line/Hi-Z | None | 2 rear line | None |
| Main outputs | Unbalanced RCA | Balanced ¼-inch | 4 × ¼-inch | 2 × ¼-inch TRS |
| Digital and MIDI | None | None | S/PDIF, 5-pin MIDI | None |
| Headphone outputs | 1 | 1 | 2 | 1 |
| Top sample rate | 192 kHz | 192 kHz | 192 kHz | 192 kHz |
In short, the Komplete Audio 2 is the two-mic, balanced-output step in the range. The Komplete Audio 6 adds line inputs, S/PDIF, MIDI and a second headphone output.
Pros and cons
Pros
- Two combo inputs with +48 V phantom power.
- Balanced ¼-inch main outputs for studio monitors.
- Up to 24-bit/192 kHz.
- Large volume knob on top.
- Direct monitoring for zero-latency tracking.
- Bus powered and light, at about 360 g.
Cons
- One headphone output, so duo podcasts need a splitter or headphone amp.
- No MIDI ports.
- No pad switches.
- No digital I/O or expansion.
- Direct monitoring is a switch, not a blend control.
Common mistakes with the Komplete Audio 2
- Leaving the input switch on line for a guitar. Passive pickups sound thin on the line setting. Choose instrument.
- Using phantom power with a ribbon mic. Check the mic’s manual first.
- Using a generic Windows driver. Install the NI driver for ASIO.
- Doubling monitoring. Turn DAW input monitoring off when direct monitoring is on.
- Mismatched stereo mic distances. Unequal spacing causes phase issues. Measure both mics.
- Unbalanced cables on balanced outputs. TS cables work, but TRS cables reject more noise over distance.
Who the Native Instruments Komplete Audio 2 is for
The Native Instruments Komplete Audio 2 suits singer-guitarists, duo podcasters and producers who want balanced connections to studio monitors. It also suits anyone recording stereo keyboards or a stereo pair of mics.
However, skip it if you need MIDI for hardware synths, two separate headphone mixes or more than two inputs. The Komplete Audio 6 covers those needs.
Setting gain on the Komplete Audio 2
Native Instruments lists a maximum mic input of +7 dBu, line input of +20 dBu and instrument input of +10 dBu. It also quotes an EIN of -127 dBu at maximum gain. Those figures give fair headroom for vocals and acoustic instruments.
- Ask for the loudest part of the performance.
- Raise gain until the input ring shows a strong, steady signal.
- Back off if the clip indicator lights.
- Aim for DAW peaks around -12 to -6 dBFS.
- Keep the gain fixed during the take.
Because there is no pad, very loud sources such as a cranked guitar amp may need the mic moved back. Alternatively, use a dynamic mic with lower output.
Buffer size and latency
Latency is set by the driver and buffer, not by the hardware alone. Small buffers keep software instruments responsive. Large buffers give plug-ins more processing time.
- Tracking: 64 or 128 samples, if your computer stays click-free.
- Mixing: 512 or 1024 samples.
- Crackles: raise the buffer one step and close other apps.
- Heavy sessions: use direct monitoring for zero-latency listening while recording.
Our buffer size guide, linked above, explains each setting in more detail.
Monitors and headphones
The balanced ¼-inch outputs suit studio monitors with TRS or XLR inputs. Balanced cables reject interference over longer runs, so they are worth using.
Native Instruments rates the headphone output at 48 mW into 33 Ω, with a maximum level of +4.2 dBu. That drives most closed-back studio headphones well. However, very high-impedance headphones may sound quieter, so check reviews of your model.
Finally, always turn the headphone level down before putting headphones on. Then raise it gradually.
Pre-session checklist
- Komplete Audio 2 selected in the DAW, with the NI driver on Windows.
- Line or instrument chosen on each input.
- Phantom power on only for condenser mics.
- Direct monitoring on and DAW input monitoring off.
- Test take recorded and checked.
Keyphrase recap: Komplete Audio 2 in brief
To sum up, the Native Instruments Komplete Audio 2 offers two combo inputs with phantom power, balanced ¼-inch main outputs, a headphone output and direct monitoring at up to 24-bit/192 kHz. It is bus powered and compact. For two-source recording on a desk, it covers the basics cleanly.
Workflow: a duo podcast on the Komplete Audio 2
Two hosts in one room is a common reason to choose this interface. The recording side is straightforward, but monitoring needs a little planning.
- Give each host a dynamic mic, and place the mics at least an arm’s length apart.
- Point each mic away from the other host to reduce spill.
- Record each mic to its own mono track at 48 kHz and 24-bit.
- Set each gain while that host speaks at full volume.
- Use a headphone splitter, or a small headphone amp fed from the outputs, so both hosts can listen.
Afterwards, edit each track separately. For example, you can trim coughs on one track without touching the other. As a result, the final episode sounds tighter than a single shared mic.
If you later add a third host, you will need more inputs. In that case, a four-input interface is the next step.
Mac and Windows notes
On a Mac, the Komplete Audio 2 appears in Audio MIDI Setup once connected. Set the format there if your DAW does not. On Windows, use the NI control panel to pick the buffer size, and select the ASIO driver in your DAW. Avoid shared Windows audio drivers for recording, because they add latency.
Recording a stereo keyboard or synth
Many keyboards and synths have left and right line outputs. The Komplete Audio 2 can capture both sides at once.
- Connect the keyboard’s left output to input 1 and its right output to input 2.
- Switch both inputs to line, and leave phantom power off.
- Set both gain knobs to the same position, then fine-tune on the loudest passage.
- Record to one stereo track or two mono tracks panned hard left and right.
Because the gains are separate, match them carefully. Otherwise, the stereo image leans to one side.
Check the current price of the Native Instruments Komplete Audio 2 on Amazon.
FAQ
Is phantom power per channel?
No. Komplete Audio 2 has one global phantom switch for both inputs.
Does it have MIDI?
No. Komplete Audio 6 adds MIDI.
Does Komplete Audio 2 have per-channel phantom power?
No, one global switch.
Are the outputs balanced?
Yes, TRS.
Does Komplete Audio 2 have MIDI?
No.
Is Komplete Audio 2 bus powered?
Yes.
Can the Komplete Audio 2 record two mics at the same time?
Yes. Both combo inputs accept XLR mics, and each arrives as its own channel in your DAW.
Shortlist the Native Instruments Komplete Audio 2 if its connections line up with your gear. Then read how to choose an audio interface before you buy.
One reply on “Native Instruments Komplete Audio 2 Review: Specs, Features and Who It Suits”
[…] Komplete Audio 2 […]