As an Amazon Associate I earn from qualifying purchases. This write-up is based on manufacturer specifications and published documentation, not hands-on testing.
The Behringer UMC22 is one of the lowest-cost ways to plug a single microphone into a computer, with a MIDAS-designed preamp, one instrument input and two ¼-inch TRS line outputs.
What the Behringer UMC22 is
The UMC22 is Behringer’s most basic U-PHORIA interface. It has one MIDAS-designed mic preamp with phantom power on a combo input, an instrument input for guitar or bass, two ¼-inch TRS line outputs and a headphone output. It records at up to 48 kHz, which is the standard rate for video and perfectly usable for music.
A direct monitor switch lets you hear the input with no computer latency. There are no MIDI ports and no insert points. Some older write-ups mention RCA outputs, but Behringer’s current page lists two ¼-inch TRS line outputs (RCA outputs belong to the UM2). It is bus powered, so it runs from one USB cable.
A first voiceover setup
A beginner with one dynamic mic records voiceover for videos. The UMC22 takes the mic on its combo input, the direct monitor switch lets them hear themselves without delay, and the two TRS line outputs feed small powered speakers. Later, an acoustic guitar can be plugged into the instrument input.
The bigger picture
Think of the UMC22 as a learning tool. It teaches the fundamentals of gain, monitoring and latency without many controls to get wrong. The trade-offs are clear: one mic input, no MIDI and a 48 kHz ceiling. If any of those will matter within a few months, starting with the UMC202HD saves buying twice.
Spec sheet summary
| Spec | Behringer UMC22 |
|---|---|
| Inputs/outputs | 2-in/2-out |
| Mic preamps | 1 |
| Preamp gain | not published on the pages we checked |
| Mic EIN | not published on the pages we checked |
| Conversion | 48 kHz |
| Connection | USB 1.1 (type B) |
| Power | USB bus powered |
| I/O detail | 1 XLR/TRS combo mic input with MIDAS-designed preamp, 1 instrument input, 2 ¼-inch TRS line outputs, 1 headphone output, direct monitor switch |
All figures are drawn from the Behringer UMC22 product page and the manufacturer’s published docs.
Features worth knowing
- One MIDAS-designed mic preamp with phantom power.
- Separate instrument input.
- Direct-monitor switch for zero-latency listening.
- Bus powered.
- Simple, few controls to learn.
Behringer UMC22 vs the alternatives
| Interface | I/O | Mic preamps | Connection | Power |
|---|---|---|---|---|
| Behringer UMC22 | 2-in/2-out | 1 | USB 1.1 | USB bus powered |
| Behringer UMC202HD | 2-in/2-out | 2 | USB 2.0 | USB bus powered |
| Steinberg UR12 | 2-in/2-out | 1 | USB 2.0 | USB bus powered |
UMC202HD adds a second preamp and 192 kHz conversion. Steinberg UR12 has a dedicated Hi-Z input with a similar single-mic layout. You can compare more models in the best audio interfaces.
What the MIDAS-designed preamp means
Behringer describes the UMC22 preamp as MIDAS-designed, referring to the console brand it owns. On a budget interface, that indicates the preamp design is borrowed from a professional range, although the rest of the unit is built to a low price. In practice, the UMC22 is best thought of as a way to learn recording fundamentals: gain staging, monitoring and managing latency. Once those are second nature, you will know which features to look for in an upgrade, such as balanced outputs, a second preamp or higher sample rates.
A first podcast setup often looks like this: one dynamic mic into the UMC22, headphones plugged into the front, and powered speakers on the TRS line outputs. That covers solo recording, voiceover practice and simple demos. When a second person joins the show, the UMC202HD is the natural next step.
Understanding the features
Bus power in practice
A bus-powered interface is simpler to carry and set up, with no adapter to forget. The trade-off is available power: phantom power and headphone level both draw on the USB port. Desktop computers usually supply enough; tablets may not.
Instrument (Hi-Z) inputs
If you record guitar, check which inputs offer Hi-Z. On some interfaces only one input has it, so plan which input the guitar uses.
How much preamp gain do you need?
A common surprise for new users is a vocal recorded with the gain near maximum that still sounds quiet. That usually means a low-output dynamic mic on a preamp without much gain. The fix is more gain, a booster, or a condenser mic, not normalising a noisy recording afterwards.
Choosing a sample rate
Most music and video work runs at 44.1 or 48 kHz with 24-bit depth. Higher rates increase file sizes and CPU load and, with ADAT, reduce channel counts. Use them when a client or project requires it.
Latency and buffer size
If you hear yourself late in headphones, either lower the buffer size or use direct monitoring, which bypasses the computer entirely.
Line outputs and cables
The two ¼-inch TRS line outputs connect straight to powered monitors. Use TRS-to-TRS or TRS-to-XLR cables, and keep runs short and away from power leads.
Getting started
- Connect USB; no external power needed.
- Plug in the mic and set gain.
- Use the direct monitor switch while recording.
- Select 44.1 or 48 kHz in your DAW.
- Connect the TRS line outputs to speakers.
Pitfalls
- Selecting 96 kHz, which the UMC22 does not support.
- Expecting two mic inputs.
- Running speaker cables alongside power leads.
What it does not do
Behringer lists the UMC22 at up to 48 kHz and does not publish gain or EIN on the product page we used. Outputs are two ¼-inch TRS line jacks plus one headphone jack. It connects over USB 1.1 and is bus powered, so one USB cable runs it.
Who should buy it
- First interface for a beginner
- Recording a single voice-over
- Guitarists who just want to plug in and practise with amp plugins
Who it is not for
- Anyone wanting sample rates above 48 kHz
- Users needing two mic inputs
- Producers who need 5-pin MIDI or insert points
If this sounds like your setup, see the Behringer UMC22 on Amazon.
You may also find these useful: audio interfaces for vocals, gain staging.
How to set up the Behringer UMC22 step by step
A clean first recording on the Behringer UMC22 takes about fifteen minutes. The order matters, because the driver and buffer choices affect every take after them. Work through these steps once, and save the settings as a DAW template.
- Install the driver on Windows. Download Behringer’s USB audio driver from the UMC22 page before you plug in. On a Mac, no driver is needed, because the unit is class compliant.
- Connect the USB cable. Plug it straight into the computer, not an unpowered hub. The UMC22 draws all its power from this cable, at a maximum of 2.5 W.
- Turn everything down. Set both gain knobs and the output knob to minimum. Then switch on your speakers.
- Pick the device in your DAW. Choose the UMC22 for input and output. On Windows, choose the Behringer ASIO driver rather than a generic one.
- Set the sample rate. Choose 44.1 kHz for music or 48 kHz for video. The UMC22 also offers 32 kHz, but it has no 96 kHz mode.
- Set the buffer. Start at 128 samples while recording. Raise it to 512 or more when you mix with many plug-ins.
- Enable phantom power only if needed. A condenser mic needs +48 V. A dynamic mic does not, so leave it off.
Next, record a ten-second test. Play it back at normal listening level before you start the real take.
Workflow: setting gain on the UMC22
Gain staging is the skill this interface teaches best. With only two gain knobs, every choice is easy to see. However, the mic input clips at +2 dBu, according to Behringer’s specifications, so loud singers need care.
- Ask the performer to sing or play the loudest part of the song.
- Raise the gain until the signal LED lights steadily.
- If the clip LED flashes, back the gain off until it stays dark on the loudest notes.
- In your DAW, aim for peaks well below 0 dBFS. Around -12 to -6 dBFS leaves safe headroom at 24-bit.
- Record, then check the waveform. Flat tops mean clipping, so lower the gain and try again.
For a deeper walk-through, read our guide to gain staging for clean recordings. The same rules apply on any interface you buy later.
Recording voice and guitar together
The UMC22 has two inputs with separate gain knobs. That means a singer-guitarist can record voice and guitar at once, on two tracks. Here is a simple routine that keeps the tracks usable.
- Input 1 (combo XLR): the vocal mic. Point it at the mouth, roughly a hand’s width away.
- Input 2 (instrument jack): an electric or electro-acoustic guitar, plugged straight in. Its impedance is 1 MΩ, which suits passive pickups.
- Two DAW tracks: arm one mono track for input 1 and one for input 2. Each part can then be edited on its own.
- Direct monitor on: switch it on, and mute the DAW track monitoring. Otherwise, you hear yourself twice.
Because the vocal mic will also pick up some acoustic guitar, keep the mic slightly above the guitar body. As a result, the two tracks stay easier to balance later.
Behringer UMC22 vs other budget interfaces
The table below compares the UMC22 with three interfaces we cover. Every figure comes from each maker’s published specifications.
| Feature | Behringer UMC22 | Behringer UMC202HD | Behringer UMC204HD | Native Instruments Komplete Audio 1 |
|---|---|---|---|---|
| Mic preamps | 1 | 2 | 2 | 1 |
| Instrument input | Dedicated ¼-inch jack | On both combo inputs | On both combo inputs | ¼-inch line/Hi-Z input |
| Top sample rate | 48 kHz | 192 kHz | 192 kHz | 192 kHz |
| Line outputs | 2 × ¼-inch TRS | 2 × ¼-inch TRS | 2 × ¼-inch TRS main, 4 × RCA playback | Stereo RCA |
| 5-pin MIDI | No | No | Yes | No |
| Insert points | No | No | 2 | No |
| Power | USB bus | USB bus | USB bus | USB bus |
In short, the UMC22 covers one voice and one instrument. The UMC202HD adds a second mic preamp and higher sample rates. Meanwhile, the UMC204HD adds MIDI and inserts for hardware.
Pros and cons
Pros
- Midas-designed preamp with switchable +48 V phantom power.
- Separate instrument input, so voice and guitar record at once.
- Zero-latency direct monitor switch.
- Two TRS line outputs for powered monitors.
- Bus powered, with a metal chassis and few controls to learn.
- Driverless on a Mac.
Cons
- One mic input only.
- Tops out at 48 kHz.
- USB 1.1 connection, per Behringer’s spec sheet.
- No MIDI ports, no inserts and no pad switch.
- Direct monitoring is an on/off switch, not a blend knob.
- Behringer does not publish preamp gain or EIN figures.
Common mistakes with the Behringer UMC22
- Leaving DAW monitoring on with direct monitor. You hear a doubled, phasey signal. Use one or the other.
- Plugging a guitar into the combo jack. The combo input is mic/line. Use the dedicated instrument jack for passive pickups.
- Turning phantom power on with a ribbon mic. Check the mic’s manual first. Many dynamic mics are fine, but some ribbons are not.
- Running through an unpowered hub. Bus-powered units can drop out when power is short. Connect directly instead.
- Normalising a quiet take. Raising a weak recording also raises its noise. Fix the gain at the source.
- Expecting 96 kHz in project settings. If a template asks for 96 kHz, the DAW may refuse or resample. Set 44.1 or 48 kHz.
When to upgrade from the UMC22
The UMC22 is a starting point, so it helps to know when you have outgrown it. Three signs are common. First, you need two mics at once, for a duet or a two-person podcast. Second, a client asks for files above 48 kHz. Third, you buy a synth or drum machine with only 5-pin MIDI.
Each sign points to a different model. Two mics point to the UMC202HD. MIDI and outboard gear point to the UMC204HD. A full band points to the four-input UMC404HD. Our guide on how to choose an audio interface walks through these choices in more detail.
Using the UMC22 for voiceover and podcasts
Spoken word is where the UMC22 makes the most sense. One voice needs one preamp, and 48 kHz is the usual rate for video. So the limits rarely get in the way.
Start with a dynamic mic if your room is untreated. It picks up less reflected sound than most condensers. Next, place the mic close, about two to four fingers from the mouth, slightly off-axis. That angle reduces popping on hard consonants.
Then set the session to 48 kHz and 24-bit. Record each episode to a fresh track, and keep a ten-second room-tone clip at the start. That clip helps noise-reduction tools later. Finally, export a WAV master before you make any compressed copy for upload.
For a remote guest, record your own side locally on the UMC22. Ask the guest to do the same, then line the files up afterwards. As a result, both voices stay clean even if the call quality drops.
Headphones and monitoring tips
The headphone jack is a ¼-inch stereo socket, and the output knob sets its level. Closed-back headphones work best while recording, because they leak less sound into the mic.
- Lower the output knob before you put headphones on.
- Use the direct monitor switch while tracking, so there is no delay.
- Switch it off while mixing, so you hear only the DAW playback.
- Check a mix on speakers too, not only on headphones.
If your headphones have a 3.5 mm plug, use a screw-on ¼-inch adapter. A loose adapter can crackle when the cable moves.
Pre-session checklist
Run through this list before every session. It takes a minute, and it prevents most lost takes.
- USB cable connected directly, and the UMC22 selected in the DAW.
- Sample rate at 44.1 or 48 kHz, matching the project.
- Phantom power on only for a condenser mic.
- Gain set on the loudest part, with the clip LED dark.
- Direct monitor on, and DAW input monitoring off.
- Enough free disk space for the session, plus a backup drive ready.
Save this as a note next to your desk. Over time, the routine becomes automatic, and that habit carries over to any bigger interface.
Check the current price of the Behringer UMC22 on Amazon.
FAQ
Is the UMC22 good enough for music?
For one mic or instrument at a time, yes; its limitations are input count and features rather than basic usability.
Does the UMC22 support 96 kHz?
No. Behringer lists it at up to 48 kHz; the UMC202HD goes to 192 kHz.
Does the UMC22 support phantom power?
Yes, it provides phantom power for condenser mics.
What sample rate does the UMC22 support?
Up to 48 kHz.
Does the UMC22 have an instrument input?
Yes, a separate instrument input for guitar or bass.
Is the UMC22 bus powered?
Yes, over USB.
Can the UMC22 record two tracks at once?
Yes. The combo mic input and the instrument input arrive as two separate channels, so a voice and a guitar can be recorded on separate tracks.
Shortlist the Behringer UMC22 if its connections line up with your gear. Then read how to choose an audio interface before you buy.
One reply on “Behringer UMC22 Review: Specs, Features and Who It Suits”
[…] Behringer UMC22 […]